11/10
Total Solution to Earthing & Lightning Protection |
9AKK106354A3360
11
Mains power protection
ESP D1 Series (Three phase)
Combined Type 1, 2 and 3 tested protector (to BS EN 61643) for use on three
phase mains power distribution systems primarily to protect connected electronic
equipment from transient overvoltages on the mains supply, e.g. computer,
communications or control equipment. Innovative remote display options allow
both protector and display to be mounted in their optimum position. For use at
boundaries up to LPZ
0
to protect against flashover (typically the main distribution
board location, with multiple metallic services entering) through to LPZ 3 to protect
sensitive electronic equipment.
Accessories
Features & benefits
–– Very low let-through voltage (enhanced protection to
IEC/BS EN 62305) between all sets of conductors (phase to
neutral, phase to earth, neutral to earth - Full Mode protection)
–– Full Mode design capable of handling partial lightning currents
as well as allowing continual operation of protected equipment
–– Repeated protection in lightning intense environments
–– Innovative multiple thermal disconnect technology for safe
disconnection from faulty or abnormal supplies (without
compromising protective performance)
–– Three way visual indication of protection status and advanced
pre-failure warning so you need never be unprotected
–– ESP XXX D1R or ESP XXX D1R/LCD units (where XXX = 208,
or 415, or 480) have a remote display that allows the
protector to be mounted close to the incoming feed or
distribution board with the display being mounted in a visible
–– ESP XXX D1/LCD or ESP XXX D1R/LCD units have backlit
LCD intelligent display offering clear status information
that can be rotated for side mounting to facilitate short
connecting leads
–– Remote indication facility allows pre-failure warning to be
linked to a building management system, buzzer or light
–– Changeover active volt-free contact enables the protector to be
used to warn of phase loss (i.e. power failure, blown fuses etc)
–– Flashing warning of potentially fatal neutral to earth supply
faults (due to incorrect earthing, wiring errors or
unbalanced conditions)
–– Through terminal facility allows series connection on low
current supplies to eliminate high additive voltage associated
with connecting leads on units installed in parallel
–– Compact space saving DIN housing
Installation
Install in parallel, within the power distribution board or directly
(via fuses) on to the supply feeding equipment. Can be installed
in series for low current supplies - see installation instructions.
For ESP D1R or D1R/LCD units, position remote display,
making sure that the cable is long enough, is unimpeded within
the cabinet, and allows a minimum of 60 mm behind the
panel front (for the interconnection cable). At distribution
boards, the protector can be installed either on the load side
of the incoming isolator, or on the closest outgoing way
to the incoming supply. Connect, with very short connecting
leads, to phases, neutral and earth. For TT installations,
contact Furse.
PE
Enhanced
Mains
Protector
EN/IEC 61643
PATENT
APPLIED
FOR
L
L'
L2
L2'
L3
L3'
N
N'
11
14
12
STATUS
Weatherproof enclosure:
WBX D4
ESP RLA HD-1
Spare 1 m cable assembly for ESP XXX
D1R or ESP XXX D1R/LCD
ESP RLA HD-2
Spare 2 m cable assembly for ESP XXX
D1R or ESP XXX D1R/LCD
ESP RLA HD-4
Spare 4 m cable assembly for ESP XXX
D1R or ESP XXX D1R/LCD
Full product range order codes can be found on pages 17/8-17/9
NOTE:
If you desire a protector with an extra high maximum surge current use the ESP M2 or ESP M4 series. If your supply is fused at 32 Amps, or less,
the in-line protectors (and their ready-boxed derivatives) may be more suitable.
Parallel connection of ESP 415 D1,
ESP 208 D1 and ESP 480 D1 series
to three phase star (4 wire and
earth) supplies (fuses not shown
for clarity)