685 / 759
Technical Hotline
+44 (0)1268 563720
685
FLOOR SYSTEMS
SCREEDED
For a full range of corresponding products,
see pages 403-411 in the product selector.
Onix Plus™ Technical
Onix Plus
™
Floorboxes
100 MIN.
55
85 MIN.
SCREED DEPTH
FINISHED FLOOR
* The Snorkel cord outlet cannot be used in depths less
than 100mm.
C
A
D
A
D
E
B
A
B
CENTRE CORD OUTLET
EDGE CORD OUTLET
BLANK LID
Lid Recess Dimensions
The dimensions in the table provide the sizes for the floor covering insert for the lid.
DIMENSION (mm)
BOX SIZE
A
B
C
D
E
200x200mm 183
183
102
31
45
265x265mm 248
248
102
63
45
340x340mm 323
323
102
101
45
Note:
Due to the weight of the lid and floor covering, a tile lifter, not the cord outlets, should be
used to lift these lids.
Screed Depth Table – for Snorkel Lid with Flush Accessories
WIRING SPACE
(mm)
FLOOR TILE THICKNESS
– INCLUDING ADHESIVE
(mm)
MINIMUM SCREED
DEPTH (mm)
MINIMUM
FINISHED FLOOR
DEPTH (mm)
25
15
85
100
25
20
80
100
25
25
75
100
25
30
70
100
35
15
95
110
35
20
90
110
35
25
85
110
35
30
80
110
45
15
105
120
45
20
105
120
45
25
95
120
45
30
90
120
l
Decide Wiring Space required: 25mm, 35mm or 45mm
l
Decided Floor Tile Thickness. (This must align with the lid depth choice)
l
Read across to determine the minimum screed depth and subsequent finish floor
thickness
Note:
When using the wave plate (CXP20215 / CXPC20215) or ST fibre plate (CXP20500 /
CXPC20500) the minimum screed depth and minimum finished floor depth must be increased
by 15mm. This will result in restrictions when utilising a 45mm wiring space.
Standards and Approvals
These products are designed to withstand
heavier than normal traffic loading as found in
office buildings. The Onix Plus
™
range supports
compliance with the requirements of the
17th Edition of the IET Wiring Regulations
(BS 7671) and to BS EN 50085 Part 1 and EN
50085-2-2. Additionally the floorboxes also
comply with IEC 60670 Parts 1 and 23.
TECHNICAL SPECIFICATION
MATERIALS
BOX LID AND FRAMES
Lid, load plate and frame manufactured in stainless
steel. Cord Outlet mouldings are manufactured from a
UL94 V2 rated nylon.
POWER GROMMET
Service outlet is die cast aluminium, brass or nickel
plated brass. The base unit is pre-galvanised steel.
Plastic parts are polycarbonate.
RAL COLOURS
Grey (GRY) = RAL 7011
Beige (BEG) = RAL 1019
FEATURE BENEFITS
l
Wet washable and IP44 when not in use
l
Tested to EN 50085-2-2 to accept 10,000N load
(5,000N load for Onix Plus Grommet)
l
Selection of lid recess depths available,
allowing for various floor depths
l
Designed to support Cat 6 structured cabling
systems
l
Wide range of power and data accessories
available to meet all requirements
l
Quality, reliability and safety come as standard
l
Provision of RCD protection supports compliance
with the 17th Edition of the IET Wiring
Regulations (BS 7671)
l
5 year guarantee
Wet Wash Test
The plain lid and the centre Snorkel outlet
lids have an Ingress Protection rating of IP44,
according to BS EN 60529:1992
Centre Cord Outlet Restrictions
This applies to the Snorkel Cord Outlet lid.