311 / 327
TECHNICAL INFORMATION
Technical information
Screening
• Boxes available with copper spray
screening to protect data outlets
from electromagnetic interference.
Part M boxes and box assemblies
• Comply with the requirements of
Part M (DDA)
• Odyssey coloured boxes (DD1510
and DD1520) with coloured flanges to
contrast with trunking cover colour.
• ESPM box assemblies with contrasting
coloured flush accessory box frames.
For colour varieties please view the
perimeter trunking pages.
Maximum
adjustment
range
Page
Reference
PowerPoles and PowerPosts
Series 1 and 2
32 - 40mm 97
PVC-U Perimeter Trunking
Mono 10
32 - 40mm 112
Compact 1
32 - 40mm 118
Compact 2
32 - 40mm 120
Compact 3
32 - 40mm 122
Mono Plus 20
32 - 40mm 114
Mono Plus 30
32 - 40mm 116
Twin165
32 - 47mm 152
Sterling Profile 1 - 3
32 - 45mm 127
Sterling Curve
32 - 40mm 133
Odyssey
32 - 40mm 109
Twin Plus
32 - 47mm 154
Sterling Profile 4 - 13*
32 - 45mm 141
XL Trunking 201 - 203
32 - 47mm 145
XL Trunking 211 - 213
32 - 47mm 149
Aluminium Trunking
Bench Trunking
32 - 47mm 182
Elegance 110
32 - 40mm 163
Elegance 170
32 - 40mm 165
Sterling Profile 3001 - 3003 32 - 40mm 168
Twin Plus
32 - 47mm 180
XL Trunking 301 - 303
32 - 47mm 172
XL Trunking 311 - 313
32 - 47mm 176
PVC-U Domestic and General Trunking
Bench Trunking
32 - 47mm 210
Power, voice and data accessories
| 311
• For close coupled assemblies, use lid
spacer (ES1WH) between boxes.
Voice and data outlet modules
(punched 6c 22 x 37mm apertures
to accept appropriate voice
or data outlets)
Fitting
• Remove front cover from assembly.
• Front fix accessories: remove the
two securing screws.
• Flush finish accessories: unclip
from back box.
• Fit appropriate voice or data outlets.
• Wire according to manufacturer’s
instructions.
• Re-fit face plate.
• Clip complete assembly into trunking
compartment.
• For close coupled assemblies, use lid
spacer (ES1WH) between boxes.
Trunking accessory boxes for
mounting standard
BS1363 wiring accessories
and Data plates
Standard boxes
• 1 gang fixing centres: 60.3mm
• 2 gang fixing centres: 120.6mm
• Depth: 30mm
Fitting
• Remove appropriate knockouts.
• Feed cables through knockout.
• Wire to accessory in accordance
to wiring regulations and
manufacturer’s instructions.
• Screw accessory to box.
• Clip complete assembly into trunking
compartment.
Adjustable boxes – two part
• 1 gang fixing centres: 60.3mm
• 2 gang fixing centres: 120.6mm
• Depth: 32 - 50mm
Fitting
• Remove appropriate knockouts.
• Feed cables through knockout.
• Wire to accessory in accordance
to wiring regulations and
manufacturer’s instructions.
• Screw accessory to box front frame.
• Press (ratchet) both components
together until required final box
depth is reached.
• Clip complete assembly into trunking
compartment.
General
MT32 13Amp pre-wired sockets,
Marshall-Tufflex BS 1363 power
assemblies and voice and data
boxes for Marshall-Tufflex PVC-U and
aluminium trunking systems (except
Sovereign Plus and steel systems)
Trunking accessory mounting boxes.
Installation
MT32 pre-wired socket range
Fitting
• Plug in incoming pre-wired lead
(from previous socket or distribution
board) to appropriate connector
mounted in socket assembly box.
• Connect selected pre-wired lead to
outgoing connector mounted on
opposite side of socket assembly box.
• Clip complete assembly into trunking
compartment.
• When trunking cover is fitted, it
should be slid between back box
frame and the loosened accessory
face plate.
• Front plate is then fully tightened
down to clamp accessory in place.
• For pre-made close coupled
assemblies, use lid spacer (ES1WH)
between boxes.
MT32 system with non-Marshall-
Tufflex socket assemblies
Fitting
• For non-Marshall-Tufflex accessories,
use pre-assembled outlet box unit.
• Connect cable tails to accessory in
accordance with wiring regulations
and fit accessory to back box.
• Connect pre-wired incoming and
outgoing leads and fit to trunking
(as above).
• For close coupled assemblies, use lid
spacer (ES1WH) between boxes.
Marshall-Tufflex
BS 1363 power assemblies
(sockets, switches, spur units)
Fitting
• Remove front cover from assembly.
• Front fix accessories: remove the
two securing screws
• Flush finish accessories: unclip from
back box.
• Remove appropriate knockout/s for
wiring.
• Wire according to wiring regulations.
• Re-assemble accessory and
re-fit face plate.
• Clip complete assembly into trunking
compartment.
Power, voice and
data accessories
Adjustable accessory box depth
by product range
p230
Product
Information
*Sterling Profile 4 - 13
The EAB1/2 can be adjusted to
45mm in the main compartment
only. Where the EBE1 Base Extension
is used the maximum adjustment
achievable is 40mm