91 / 108
91
Onix Plus™
Technical
technical hotline +44 (0)1268 563720
screeded floor systems
Onix Plus™ Floorboxes
Onix Plus™Floorboxes and Power Grommets are a unique, innovative
solution to hard floor power and data distribution requirements
in screed floors with coverings such as laminate, wood, stone
and marble.
l
Wet washable and IP44 when not in use
l
Tested to EN50085-2-2 to accept 10,000N load
l
Selection of lid recess depths available, allowing for various floor depths
l
Designed to support Cat 6 structured cabling systems
l
Wide range of power and data accessories available to meet all
requirements
l
Quality, reliability and safety come as standard
l
Provision of RCD protection supports compliance with the 17th Edition
Wiring Regulations
l
5
year guarantee
Materials
Round Aluminium Floorbox
Lid and Frame manufactured in die cast aluminium. Snorkel Cord Outlet
mouldings are manufactured from a UL94 V2 rated nylon.
Box Lid and Frames
Lid, load plate and frame manufactured in stainless steel. Cord Outlet
mouldings are manufactured from a UL94 V2 rated nylon.
Power Grommet
Service outlet is die cast aluminium, brass or nickel plated brass. The base
unit is pre-galvanised steel. Plastic parts are polycarbonate.
RAL Colours
Grey (GRY) = RAL 7011
Light Grey (LGY) = RAL 7046
Beige (BGE) = RAL 1019
Lid Recess Dimensions
The dimensions in the table provide the sizes for the floor covering insert
for the lid.
Wet Wash Test
The plain lid and the centre Snorkel outlet lids have an Ingress Protection
rating of IP44, according to BS EN60529: 1992
Standards
These products are designed to withstand heavier than normal traffic loading
as found in office buildings. The Onix Plus™ range supports compliance with
the requirements of the latest edition of the IEE Wiring Regulations (BS
7671)
and to BS EN50085 Part 1 and EN50085 Part 2-2. Additionally the
floorboxes also comply with IEC 60670 Parts 1 and 23.
Centre Cord Outlet Restrictions
This applies to the Round Aluminium Floorbox and the Box Lid with Snorkel
Cord Outlet.
Screed Depth Table – For Snorkel Lid with Flush Accessories
Wiring
Space
(
mm)
Floor Tile
Thickness
-
including
adhesive (mm)
Minimum Screed
Depth (mm)
Minimum
Finished Floor
Depth (mm)
25
15
85
100
25
20
80
100
25
25
75
100
25
30
70
100
35
15
95
110
35
20
90
110
35
25
85
110
35
30
80
110
45
15
105
120
45
20
105
120
45
25
95
120
45
30
90
120
l
Decide Wiring Space required: 25mm, 35mm or 45mm
l
Decided Floor Tile Thickness. (This must align with the lid depth choice)
l
Read across to determine the minimum screed depth and subsequent
finish floor thickness
Note:
When using the wave plate (CXP20215 / CXPC20215) or ST fibre plate
(
CXP20500 / CXPC20500) the minimum screed depth and minimum finished
floor depth must be increased by 15mm. This will result in restrictions when
utilising a 45mm wiring space.
C
A
D
A
D
E
B
A
B
Centre Cord Outlet
Edge Cord Outlet
Blank Lid
Note:
Due to the weight of the lid and floor covering, a tile lifter, not the
cord outlets, should be used to lift these lids.
Box size Dimension (mm)
A
B
C
D
E
200
x200mm 183
183
102
31
45
265
x265mm 248
248
102
63
45
340
x340mm 323
323
102
101
45
*
The Snorkel cord outlet cannot be used in depths less than 100mm.